Revitalization of the Electronic Sound System at Surabaya Cathedral

Documentation of Acoustic Analysis, Sound System Electronic Engineering, and Psychoacoustic Calibration – By: Hardy Nanda

History

As the city of Surabaya expanded southward, the Catholic population in the region concurrently grew. Consequently, the Kepanjen Church was no longer able to accommodate the entire congregation attending services. This catalyst prompted the initiative to construct a new church in the southern district of Surabaya.

The endeavor to secure a suitable location proved to be a protracted and complex process, spanning from 1911 to 1919. Several prospective sites were seriously deliberated: Tunjungan: An 800-square-meter plot situated near the Rathkamp pharmacy, valued at 24,000 guilders. Embong Wungu/Kaliasin: A 2,633-square-meter plot priced at approximately 43,000 guilders. This location was highly favored; however, the plan was ultimately abandoned after a municipal survey revealed an exceptionally high groundwater table, rendering it unsafe for the construction of a large edifice. Tegalsari: A 6,618-square-meter plot. Plans for this location encountered numerous obstacles, including protests from local residents and the failure to raise 50,000 guilders through bonds for funding. Ketabang: Land was available, but it was strictly offered on a 75-year lease and was not available for purchase.

The location search polemic finally reached a resolution in 1919. Following intensive deliberations, a parcel of land located at the intersection of Anita Boulevard (presently Jalan Polisi Istimewa) and Boschlaan was selected for the construction of the new church and rectory. Construction subsequently commenced. The architect, Mr. Beek, estimated an initial cost of 160,000 guilders. The laying of the cornerstone took place in 1920, although historical accounts present two differing dates: August 11, 1920, and October 26, 1920.

Designed by the ED CYPRESS BUREAU and constructed by the architectural firm HUSWIT-FERMONT, the church edifice was built utilizing a Basilica structural form. Ultimately, on July 21, 1921, the church—which boasts a capacity of 900 congregants—was blessed by Mgr. Luypen and consecrated as the Church of the Sacred Heart of Jesus. The total construction expenditure culminated in 216,143.27 guilders.

A historic milestone occurred on July 1, 1923, when the Jesuit Fathers, who had pioneered the Catholic mission in Surabaya for 64 years (1859–1923), transferred the pastoral care of the Church of the Sacred Heart of Jesus to the Lazarist Fathers (CM). The newly erected church building initially faced criticism, primarily due to its tower design, which was likened to a factory structure, as well as the presence of several structural flaws. In 1925, the building was on the verge of collapse, necessitating comprehensive repairs to its foundation in 1926. The institutional development continued to progress: on February 15, 1928, Surabaya was designated as an Apostolic Prefecture, and was subsequently elevated to an Apostolic Vicariate on October 16, 1941. The culmination of this growth occurred on January 3, 1961, when Surabaya was elevated to the status of a Diocese, with Mgr. Yohanes Klooster, CM, serving as its inaugural Bishop.

The journey of the Cathedral has not been without its adversities. During the wartime era, the church complex was abandoned and suffered substantial damage, eventually undergoing extensive renovation in 1951. A dark chapter also unfolded on October 15, 1967, when the church was subjected to a grenade attack by individuals affiliated with the PKI (Indonesian Communist Party), although it fortunately did not result in severe structural damage. Various repairs and enhancements have been continuously undertaken over the decades to maintain this "spoiled sweet girl"—an affectionate moniker bestowed upon the church due to its seemingly perpetual demand for attention. These efforts have ranged from repairing a termite-infested roof in 1972 and paving the courtyard in 1982, to the construction of a Marian Grotto in that same year and the establishment of a more adequate security post in 1996. All of these endeavors serve as a testament to the dedication and profound care demonstrated by the congregation and the broader community in preserving their house of worship.

Introduction

The Surabaya Cathedral was constructed in 1921. This signifies that as of 2026, this historic edifice is over a century old. A hundred years ago, modern sound system technology (electronic loudspeakers) had not yet been invented. This subsequently raises an intriguing question: for a building of such immense proportions—measuring approximately 50 meters in length from end to end, roughly 20 meters in width, with a ceiling height exceeding 10 meters, and a total air volume reaching approximately 9,000 cubic meters—how could the voice of the worship leader at the front be heard clearly all the way to the farthest congregation seats at the rear?

The answer lies in the combination of the environmental tranquility of the past and the architectural genius of the building itself.

Looking Back at the Past: The Acoustic Secrets of 1926

In the 1900s, architects and church builders already possessed a profound understanding of how sound propagates within an enclosed space. Their ability to design a 9,000-cubic-meter volume space capable of distributing sound evenly without electrical amplification was a synthesis of empirical architectural traditions passed down for centuries and the dawn of modern acoustic science.

When the Surabaya Cathedral was constructed in 1921, mathematically-based architectural acoustics had already been established. In the late 1890s, a physicist named Wallace Clement Sabine successfully formulated the equation for reverberation time (RT60), and in 1900, the Boston Symphony Hall became the first building in the world designed entirely with precise acoustic calculations. This signifies that the awareness of the correlation between room volume and reflective wall materials was already understood and applied by architects of that era.

However, the historical acoustic success of the Surabaya Cathedral was not merely the result of theoretical formulas on paper, but rather a design that intentionally utilized three laws of physics and human behavior:

1. The Building as a "Passive Amplifier" (Natural Loudspeaker)
Naturally, pure sound emanating directly from a human mouth (direct sound) attenuates rapidly as distance increases. Inside the Surabaya Cathedral, this direct sound depletes its energy once it surpasses the critical distance, which is beyond 12.80 meters from the altar.

To overcome this physical limitation, the architect designed the building with an elongated shape, massive walls approximately 60 cm thick that are highly rigid and sound-reflective, and a curved, cylindrical vault ceiling stretching from the front to the rear with a substantial radius.

This geometric form was deliberately created to maximize sound reflection and generate an acoustic phenomenon known as a Reverberant Plateau. Because the walls and curved ceiling reflect almost all sound energy from the top down (indicated by a very low Lateral Fraction value of 0.05 – 0.08, as noted at the end of the original article), the sound energy is not lost but instead amalgamates into a dense and stable "reverberation cloud." It is this reverberation cloud within the reverberant plateau area that assumes the task of carrying the sound from the front, propagating it up to approximately 43 meters to the rearmost rows of seats.

2. Liturgy Adapting to Spatial Acoustics
Consequent to the 60-cm-thick walls and the curved vault, the reverberation time inside the Surabaya Cathedral became exceptionally long, reaching approximately 4.2 seconds, with a natural reverberation frequency (room resonance) below 50 Hz. In the study of acoustics, a 4.2-second reverberation is essentially a nightmare for fast-paced speech, as the words will overlap and mask one another.

A century ago, however, this architecture worked in perfect harmony with the Catholic liturgical practices of the time, which heavily utilized Gregorian Chants or prayer recitation techniques with a slightly slower tempo and intonation.

When a worship leader at the altar or pulpit spoke with clear articulation, proper sound projection, and a sufficiently slow tempo while sustaining their vocal pitch, the sound actually "activated" (excited) the building's resonant frequencies. The vocal tones seemingly rode the reflective energy within the reverberant plateau, resulting in a highly majestic and grandiose sound. Concurrently, the pauses between words were naturally regulated to allow the reverberation from the preceding syllable to decay, preventing it from masking the subsequent syllable. In short, the people of that era adapted their speaking pace to the natural characteristics of the room.

3. Environmental Tranquility in 1926
The final determining factor was the tranquility of the environment. In 1926, the Surabaya Cathedral building was situated in the midst of a vast open field (as evidenced by historical photographic documentation), devoid of passing motor vehicles. It is assumed that the background noise floor during that period was exceedingly low, hovering only between 32 and 35 dB (equivalent to the quiet ambiance of a library).

Biologically, for the human ear to clearly hear and comprehend speech, the speaker's voice merely needs a loudness differential (known as the Signal-to-Noise Ratio, or SNR) of +20 to +25 dB above the ambient noise of the room. Thus, in 1926, a worship leader only needed to speak at a loudness level of 50 to 60 dB (normal conversational volume without the need to shout). Assisted by the energy reflection from the reverberant plateau, utterances from the altar could be heard with full clarity all the way to the rearmost congregation seats.

But Time Dictated Otherwise: The Collapse of the Signal-to-Noise Ratio in the Modern Era

A century later, the environmental conditions surrounding the Cathedral have changed drastically. Now, in 2026, the Surabaya Cathedral is situated directly facing a highly congested road, as it serves as one of the main traffic arteries of the city of Surabaya. Furthermore, the addition of air conditioning systems inside the building contributes a continuous mechanical roar, compounded by the increasing density of activities in the Cathedral area.

When recent field measurements were conducted, the room's noise floor during services was found to have surged drastically to between 60 dB and 65 dB.

This collapse of the ratio between the speaker's voice and the room's ambient noise (Signal-to-Noise Ratio / SNR) constitutes the root problem for ancient churches today:

  • Condition in 1926: The room noise was merely 32–35 dB. A speaker only needed to project a voice of 50–60 dB to achieve the ideal differential (+20 to +25 dB).

  • Condition in 2026: The room noise has escalated to 60–65 dB. To maintain a +25 dB differential for clear audibility, the pure sound from the preacher or worship leader's mouth would have to constantly pierce the 85 dB to 90 dB mark (equivalent to shouting at the top of one's lungs unceasingly). Biologically, this is an impossible feat for the human vocal cords.

In tandem with the progression of time and the demands of modern circumstances, sound systems were installed to assist in amplifying the voice. And it is precisely at this juncture that a whole new set of problems began.

The Disaster of Conventional Sound System Installation and Room Acoustic Analysis

Why does the installation of a sound system actually trigger new problems? This is because the traditional sound system approach often focuses on only one aspect: "increasing the volume to make it louder."

Projecting a massive Sound Pressure Level (SPL) rawly into a 9,000-cubic-meter vault without controlling the direction of sound dispersion brutally awakens the 4.2-second reverberation "monster." Instead of extending the reach of the original voice (direct sound), the excessive sound energy from the speakers aggressively strikes the cylindrical ceiling and thick walls, subsequently multiplying random reflections in all directions. Consequently, the room's echo swallows the clarity of the speech itself. The space becomes exceedingly noisy and resonant, yet the preacher's words are entirely indistinguishable (low intelligibility); the sound is loud, but entirely unclear.

In order to correctly install and configure a sound system within the Surabaya Cathedral, it is imperative to first understand the sound propagation map within this space.

Sound Propagation Map Based on Distance from the Altar Edge

Based on acoustic physics calculations, the following delineates what sound waves experience as they propagate from the edge of the altar toward the rearmost seats:

  • At a distance of approximately 5 meters from the altar edge: Direct sound is dominant (near-field transition zone). The congregation in the front rows still hears the pure sound directly from its source with utmost clarity.

  • At a distance of approximately 8 meters from the altar edge: Direct sound remains dominant. The direct sound is still more potent than the room's reverberation.

  • At a distance of approximately 12 meters from the altar edge: Surpassing the critical distance. This is the boundary point where the strength of the direct sound from the front has attenuated to become equal in loudness to the room's reverberation.

  • At a distance of approximately 16 meters from the altar edge: The reverberant field begins to dominate. The room's echo starts to become louder than the original sound.

  • At a distance of approximately 20 meters from the altar edge: Dominance of spatial reflections. The sound heard by the congregation is now dominated by reflections from the walls and ceiling.

  • At a distance of approximately 24 meters from the altar edge: The dominance of spatial reflections becomes increasingly dense.

  • At a distance of approximately 28 meters from the altar edge: Entering the Reverberant Plateau zone.

  • At a distance of approximately 32 meters from the altar edge to the end of the room: Reverberant Plateau.

Summary of Surabaya Cathedral Acoustic Parameters

  • Room Volume: Approximately 9,000 cubic meters.

  • Reverb (Reverberation Time / RT60): Exceeds 4.2 seconds (sound only dissipates after 4.2 seconds).

  • Resonance (Resonant Frequency): Below 50 Hz (the room easily vibrates and rumbles at low bass frequencies).

  • Lateral Fraction (LF): 0.05 - 0.08 (the ratio of lateral reflections from the side walls is very minimal; meaning sound reflection is heavily dominated by vertical reflections from the ceiling vault pressing straight down).

  • Dominance of Spatial Reflections: Begins to take over at a distance of 20 meters.

  • Start of Reverberant Plateau: Theoretically calculated to begin at a distance of approximately 22 meters.

  • Max Reverberant SPL (Maximum Reverberation Loudness Limit): Approximately 95 dB.

Field Notes vs. Theory:

The data above was derived from mathematical calculations based on acoustic principles. Interestingly, when actual field measurements were conducted using a Sound Level Meter (SLM), the reverberant plateau phenomenon (the point at which sound volume ceases to decrease and transforms into a uniform cloud of echo) was found to already occur starting at a distance of approximately 20 meters from the edge of the altar.

Due to the nature of this space, a modern sound system can no longer rely on conventional speakers (raw point sources) that disperse sound in all directions. To maintain vocal intelligibility within the reverberant plateau area, two absolute prerequisites are required:

  1. The utilization of speakers with highly narrow and focused directivity—projecting sound straight toward the congregation's ears while curtailing sound dispersion toward the walls or the upper vault.

  2. The execution of highly precise perceptual time-delay alignment on the supplementary speakers (delay lines), ensuring that the congregation's brains continue to process the sound as if it is arriving directly from the main altar without exciting destructive room reverberation.

Why Did the Previously Installed Sound System Sound "Blurred"?

Prior to the revitalization process, we cataloged all the existing speaker equipment installed inside the Surabaya Cathedral, which consisted of:

  • Altar Position (speakers facing into the altar): A pair of Audac Xeno6 point source speakers (serving as monitors for the worship leader). This was an ill-advised choice, as point source speakers possess a considerably wide dispersion angle and strike a broader surface area, thereby generating uncontrolled reverberation.

  • Main Speakers (Main Pillars): A pair of Audac KYRA24 column speakers.

  • Subwoofer Speakers: A pair of Audac BASO10s placed in close proximity to the main speakers, yet not physically aligned.

  • First Delay Speakers: A pair of Audac KYRA24 column speakers.

  • Second Delay Speakers: A pair of Audac KYRA12 column speakers.

  • Third Delay Speakers: A pair of Audac KYRA12 column speakers.

  • Fourth Delay Speakers (under the balcony): A pair of Bose 802 point source speakers.

  • Upper Balcony Area (choir monitors): A pair of Yamaha DBR12 point source speakers. This was also an ill-advised choice, as point source speakers have a considerably wide dispersion angle and strike a larger surface area, creating uncontrolled reverberation—especially given their position above the balcony in very close proximity to the semi-circular vault that extends from the front to the rear.

When this entire system was activated, the resulting sound within the room was either indiscernible or reasonably loud but unclear. Upon analysis, this sonic chaos was attributed to six inappropriate factors:

  • An excessive number of speakers, which further pumped reverberant energy into the space.

  • A complete failure to account for the reverberant plateau phenomenon occurring from the 20-meter mark.

  • The altar and balcony monitor speakers were not time-aligned (not delayed) relative to the other speakers, causing their sound to bleed and collide with the sound from the main speakers.

  • Incorrect mounting heights and aiming angles of the speakers, resulting in a substantial amount of sound striking the ceiling vault.

  • The use of inappropriate speaker types for specific locations (such as utilizing wide-dispersion point source speakers in areas highly prone to reflection).

  • A hidden issue with the speaker cables: The discovery of 16 AWG speaker cable runs stretched to lengths of 60 to 80 meters!

In the laws of audio electrical engineering, running a cable as thin as 16 AWG for 60 to 80 meters results in massive signal loss along the path. Based on our theoretical calculations, a power loss of up to 38.9% occurred within these cables.

As a combined result of substantial Total Harmonic Distortion (THD), misaligned time delays, an excessive quantity of speakers, and misplaced speaker types, the congregation's ears ultimately perceived three separate sounds arriving in close succession and overlapping. Akin to viewing a shaky, out-of-focus photograph, the sound inside the church was blurred; low frequencies (bass) and high frequencies (treble) masked one another, and the intricate details of speech articulation were entirely lost.

Electrical Solution: Overcoming Cable "Loss" Without Dismantling Heritage Walls

The most ideal step to address undersized cables would naturally be to replace them with larger ones. However, due to the circumstances and conditions of a century-old Cathedral building that preclude the dismantling of cable conduits behind the walls, we had to adopt a different engineering workaround.

The solution was to relocate two amplifier units to a position closer to the speakers (thereby shortening the cable runs to approximately 30 meters), and to replace one amplifier unit for the main Audac KYRA24 speakers from an Audac SMQ750 (750 Watts) to an Audac SMQ1250 (1,250 Watts).

To a layperson, upgrading an amplifier to a significantly higher power rating might sound like an extravagance. Yet, herein lies the primary salvation! The relationship between cable gauge, cable run length, and amplifier power plays a life-or-death role in sound clarity. By adjusting the amplifier model and drastically reducing the long speaker cable runs as much as possible, THD and other unnecessary distortions were vastly minimized. Consequently, the DSP could be maximally utilized to mitigate acoustic phenomena, rather than being exhausted on resolving technical flaws and compensations that should not have been necessary. The focus shifted entirely to resolving the existing acoustic phenomena.

What Happens When Speaker Cables Are Too Small and the Runs Are Too Long?

Imagine the amplifier as a water pump, the cable as the hose, and the speaker as a waterwheel at the end of the hose. If the pipe is too narrow and excessively long, at least four detrimental effects are guaranteed to occur:

1. A Drastic Drop in Damping Factor:

The damping factor is the ratio of an amplifier's ability to control and "brake" the back-and-forth movement of the speaker cone, particularly at low/bass frequencies. Akin to driving a car, the amplifier is not only tasked with pressing the accelerator (pushing the speaker cone) but must also possess potent brakes to halt the cone's vibration precisely on time. When cable resistance increases due to overly long and thin cables, the amplifier loses its electromagnetic "braking grip" on the speaker's voice coil. As a result, the speaker cone overshoots and continues to vibrate on its own, producing muddy, boomy bass and losing its sharp initial impact (punch or transient).

2. Power Loss (Insertion Loss)

A long, thin cable acts as a resistor that chokes the flow of electricity mid-way. A significant portion of the amplifier's power never reaches the speaker, but is instead wasted and converted into heat energy along the cable (in this case, reaching 38.9%). This truncates the maximum Sound Pressure Level (SPL) and renders the sound weak and lethargic.

3. Frequency Response Fluctuations (Voltage Divider Effect)

The impedance load of a speaker is not flat; rather, it constantly fluctuates depending on the pitch of the note being played (it is reactive). When high cable resistance interacts with this fluctuating speaker load, a voltage divider circuit effect is created. The detrimental consequence: the tonal coloration of the sound emitted by the speaker alters unevenly on its own (as if someone were randomly adjusting the Equalizer settings), and most dangerously, this triggers phase shifts or timing deviations in the electrical waves, completely disrupting the precision of the time-delay alignment calibration between speakers.

4. Risk of Overheating and Distortion

When handling high power and low impedance loads (such as 4-Ohm or 2-Ohm speakers), overly thin cables will struggle immensely to conduct dense electrical currents. An amplifier forced to work extra hard to push through these narrow cables will run out of headroom faster (clipping earlier), causing the sound to become distorted and harsh. Furthermore, excessive heat in thin cables risks melting the cable insulation and triggering a short circuit.

Why Was Upgrading the Amplifier to the Audac SMQ1250 Highly Advantageous?

By increasing the amplifier capacity for the Audac KYRA24 speakers from the SMQ750 to the SMQ1250 and shortening the cable runs to around 30 meters (resulting in a cable resistance of approximately 0.78 Ohms), we secured three highly significant technical advantages:

1. The Ability to Dampen Back EMF (Electromotive Force)

Column speakers like the Audac KYRA24 house 24 small speaker units (drivers) within a single pillar that move back and forth synchronously. According to the laws of physics, when those 24 voice coils return to their resting positions, they act like a bicycle dynamo (generator), sending a reverse electrical current (Back EMF) traveling back down the cable toward the amplifier! Because the 30-meter cable has already choked the Damping Factor, this "tidal wave of reverse current" from the 24 drivers will slam into the output stage components inside the amplifier. The Audac SMQ1250 amplifier features a much more colossal architecture of output components and power storage (capacitor banks / power supply) compared to the SMQ750. Like an impenetrable fortress, the SMQ1250 is capable of "swallowing" and dampening the impact of this Back EMF reverse current without allowing it to contaminate the new audio signals currently being driven forward to the speaker.


2. Preventing Micro-Clipping on Reactive Loads

The nominal 4-Ohm specification on the KYRA24 speaker is merely an average figure on paper. At certain frequencies, the combined load of these 24 drivers can plummet much lower and become extremely demanding (reactive load). When processing high-energy audio signals, such as when playing a sweep test tone (LogSweep or pink noise) during the acoustic measurement process, the amplifier is required to deliver a massive instantaneous burst of current (transient current) through the ± 0.8 Ohm cable resistance. Under such a heavy load, the power supply on a smaller amplifier (SMQ750) could experience a momentary voltage drop (sagging). This occurrence triggers micro-clipping—a micro-scale distortion so rapid that it does not even trigger the red indicator light (clip LED) on the amplifier, yet it is immediately perceived by the human ear as a harsh and fatiguing sound. The SMQ1250 amplifier possesses an exceedingly abundant current reserve for this load, ensuring the sound waveform remains perfectly rounded and clean.


3. Reduction of Mechanical Distortion (Acoustic THD)

The sonic distortion we hear in a room is acoustic distortion (the physical imperfections in the movement of the speaker cone), not merely electrical distortion at the amplifier terminals. Because the SMQ1250 exerts vastly superior current control (even when traversing 30 meters of cable), it can force the 24 speaker cones of the KYRA24 to move much more orderly, cohesively, and precisely in accordance with the original sound waveform. When the speaker cone movement is more mechanically controlled (reducing instances of cone deformation or cone break-up), the speaker's mechanical distortion drops drastically. The result is immediately audible as an overall reduction in Total Harmonic Distortion (THD): the sound becomes pristine, composed, and highly detailed.

Rearrangement Strategy: Rotating Speakers Without Purchasing New Ones

After understanding the acoustic character of this century-old building and rectifying the electrical issues concerning the cables and amplifiers, we also replaced one audio processing brain unit (DSP) from the Phaselab brand to XTA.

Why did the DSP need to be replaced? Because to tame the heavily reverberating resonant frequencies of the Cathedral space, we required volume cuts at specific frequencies (gain cuts on the Parametric Equalizer / PEQ feature) that were extremely deep, reaching -25 dB. The previously installed Phaselab DSP only had a maximum cut limit of -12 dB, which was insufficiently deep to "kill" the room's resonant reverberation.

So, what was the fate of the speakers? After inspecting the condition and specifications of all the existing speakers, it turned out that not a single new speaker needed to be purchased! The existing speakers were still highly viable for use; only their excessive quantity had to be reduced, and their positions needed to be rotated (swapped) to match the function and acoustic character of each room zone:

  • Main Speakers (Retaining the Audac KYRA24): Their position mounted on the front main pillars was lowered so that the very bottom of the speaker was only 1 meter from the main floor. The objective was absolutely crucial: ensuring the vertical projection angle swept straight across the congregation's ears and steered clear of the curved vault on the room's ceiling. Powered by the Audac SMQ1250 on channels 1 and 2.

  • Subwoofer Speakers (Retaining the Audac BASO10): Their position was shifted to be physically aligned straight with the Main Speakers. Why did they need to be physically moved when DSP technology was available? Because the correct principle of audio engineering is: the functions within the DSP should be focused on assisting acoustic adaptation to the room, rather than being squandered on correcting uncohesive (non-coherent) speaker placement errors. By physically aligning the speakers from the outset, the calibration process became vastly purer and more accurate. Powered by an Audac SMQ500 using a bridged combination for each subwoofer unit.

  • Middle Delay Speakers (Replaced from Audac KYRA12 to Audac KYRA24): Instead of using multiple rows of delay speakers as before, the quantity was trimmed and replaced by a single pair of Audac KYRA24s (which possess a vertical focal power twice as sharp as the KYRA12). These delay speakers were positioned precisely at the border of the critical area where the reverberant plateau occurs. The placement of this point had to be exceedingly precise; if it missed by even a slight margin, the sound from these speakers would be overpowered by the room's reverberation and could never be calibrated. Powered by the Audac SMQ1250 on channels 3 and 4.

    Altar Monitor Speakers (Replaced from Point Source Audac Xeno6 to Column Audac KYRA12): The monitor speakers for the worship leader, which previously utilized wide-dispersion speakers (Xeno6), were replaced using KYRA12s (repurposed from the old delay speakers). These speakers were concealed behind the pillars, governed by a strict rule: the top height of these KYRA12 monitor speakers had to be exactly identical to the top height of the Main KYRA24 speakers. Powered by the Audac SMQ750 on channels 1 and 2.

  • Under-Balcony Speakers (Replaced from Bose 802 to Audac Xeno6): The mounting position remained the same beneath the balcony, but the Bose 802 units were removed and replaced by the Audac Xeno6 units that were previously at the altar. Because the under-balcony area has a lower ceiling, the size and character of the Xeno6 are far more suitable for operating in this zone. Powered by the Audac SMQ750 on channels 3 and 4.

  • Choir Monitor Speakers Above the Balcony (Replaced from Point Source Yamaha DBR12 to Column Audac KYRA12): The remaining pair of KYRA12 units was relocated above the balcony to replace the Yamaha DBR12s. Their mounting height was meticulously measured to ensure their projection angle aimed directly at the choir members and did not strike the walls or the ceiling curve, which could trigger rogue reflections that would be impossible to calibrate. Powered by the Audac SMQ500 on channels 1 and 2.

With this intelligent rotation, the Bose 802 and Yamaha DBR12 units were retired from the room, the number of sound source points became fewer and cleaner, and each speaker now operates exactly in accordance with its expertise.

Time-Delay Calibration Process Using GCEDAC (Based on FRESL Psychoacoustics)

After the number of speakers was reduced, their physical positions corrected, signal routing organized, and the amplifiers and DSP replaced, we arrived at the most decisive culminating stage: the time-delay alignment calibration process utilizing the GCEDAC software.

Calibrating a room with a reverberation time exceeding 4.2 seconds is an extraordinary challenge. If we utilize conventional measurement tools that merely read wave reflections in raw mathematical terms, these tools will be "deceived" by the relentless barrage of room echoes.

This is where GCEDAC provides a major breakthrough. The GCEDAC calibration software was independently designed and developed by the author (Hardy Nanda) based on FRESL psychoacoustic research parameters. The fundamental principle of FRESL stems from the physiological facts of the human auditory system: when the human ear and brain process and perceive low-frequency (bass) and high-frequency (treble) sounds, there is a non-linear time gap influenced by multiple factors. One of these factors is the magnitude of the room's reverberation time and the decay across its frequency range. This implies that the cochlea inside the human ear does not function like a standard microphone; high and low notes are processed at varying neural speeds. GCEDAC aligns the time between speakers in accordance with the physiological mechanics of the human ear.

Once all room acoustic calculations, speaker position predictions and corrections, and power electronics calculations for the sound system were completely mapped out by Hardy Nanda, the subsequent step was executing all configurations within the XTA DSP and the Audac SMQ series amplifiers. This encompassed crossover frequency boundary designs, filtering (PEQ), power settings, and limiters. Subsequently, the time-delay alignment calibration process utilizing the GCEDAC software commenced, executed directly by Hardy Nanda alongside Anak Agung Made Ruandaru, who served in the capacity of critical listening (critical auditory verifier) to ensure the software's calculation results synthesized perfectly with human auditory perception:

1. Calibrating the Altar Monitor Speakers to the Subwoofers (First Step)

In a conventional room, technicians typically initiate calibration with the Main Speakers. However, because the Surabaya Cathedral possesses a reverberation time exceeding 4.2 seconds and a remarkably extensive reverberant plateau, the very first speakers that must be calibrated are the Altar Monitor Speakers relative to the Subwoofers! Why begin with the altar monitors? Because the moment the worship leader speaks, the sound energy from these altar monitor speakers immediately reflects and propagates into the rear reverberant plateau area with striking clarity. Subwoofers exclusively emit low-frequency sounds, which propagate omnidirectionally (spreading in all directions). If the altar monitors are not tamed and time-locked to the subwoofers from the outset, the resulting non-coherent sound bleed will devastate the entire soundscape within the congregation space.

2. Calibrating the Main Speakers to the Subwoofers and Altar Monitors

After the time delay for the altar monitor speakers was determined and locked, we then established the time delay for the Main Speakers (Audac KYRA24) relative to the Subwoofers (Audac BASO10). Because the altar monitors were previously locked with the subwoofers, aligning the Main Speakers to the subwoofers automatically aligned the Main Speakers' time delay to both the Altar Monitor Speakers and the Subwoofers simultaneously as a single cohesive unit. Quite fascinating, is it not?

3. The High-Level Challenge of the Delay Speakers

The subsequent phase involved calibrating the Delay Speakers (Audac KYRA24 in the middle of the room). This process demanded an exceptionally high level of precision. Why? Because the time delay for the Delay Speakers in the center of the church cannot rely solely on the Main Speakers; rather, it must be synchronized simultaneously against four sound sources at once:

  1. The sound from the Altar Monitor Speakers,

  2. The sound from the Main Speakers,

  3. The sound from the Subwoofers, and

  4. The residual sound energy still suspending and lingering within the reverberant plateau!

Utilizing conventional measurement methods to align one speaker against four variables amid a 4.2-second reverberation would be immensely complex, bewildering, and highly likely to never yield the most accurate time-delay value. However, by utilizing GCEDAC, we can instantly map and comprehend what is occurring in the air, determining the comprehensive time delay between speakers with absolute precision and without the slightest confusion.

4. The Secret of the Measurement Points for the Under-Balcony and Upper-Balcony Speakers

The final, equally compelling aspect occurred when we calibrated the Under-Balcony Speakers (Audac Xeno6) and the Upper-Balcony Monitor Speakers (Audac KYRA12). While it is standard practice to measure speakers by placing the microphone directly in front of the unit being measured, at the Surabaya Cathedral, we specifically chose not to listen to or measure directly in front of or behind those balcony speakers. Instead, we stood and positioned the measurement point squarely in the middle (in between) the Delay Speakers, the Under-Balcony Speakers, and the Upper-Balcony Speakers.

Why measure in the boundary area among these three speakers? Because the acoustic characteristics of the Cathedral—featuring a potent reverberant plateau and an exceptionally low Lateral Fraction value (0.05 – 0.08)—cause the sound reflections from the upper vault to drop directly into the transition zone before the balcony. By capturing the measurement point precisely in their convergence zone, GCEDAC can lock the time-delay transition, allowing the sound from the middle, under-balcony, and upper-balcony speakers to seamlessly fuse without any audible echo collisions.

The Final Results of the Revitalization

Through a comprehensive approach—ranging from understanding the building's 1926 acoustic history, mapping the reverberant plateau zones, rectifying power loss in the 16 AWG cables via Audac SMQ1250 amplifier and XTA DSP upgrades, and rotating speaker positions to prevent projection into the ceiling vault, to aligning time delays based on human psychoacoustics (FRESL) using GCEDAC—the sound within the Surabaya Cathedral has undergone a total transformation.

Today, there are no longer three shadowed, overlapping sounds colliding and causing auditory fatigue. Even though the building's natural reverberation time remains 4.2 seconds, just as it was exactly 100 years ago, the spoken words of the worship leader from the altar are now focused, pristine, cohesive, and sound as if they are speaking right in front of the congregation—from the very front row to the farthest corners below and above the balcony.

Acknowledgments

The sound system revitalization in this century-old historical edifice could not have been realized without the trust, support, and hard work of various parties. With profound gratitude, we extend our deepest appreciation and thanks to:

  • RD. Cornelius Triwidya Tjahja Utama, as the Head Parish Priest of the Sacred Heart of Jesus (Surabaya Cathedral), for his blessing, trust, and vision in safeguarding the worship comfort of the entire congregation.

  • Mr. Yohan Setia Putra (BGKP Sarpras), for his coordination, full support, and highly transparent discussions throughout the design and field execution process.

  • Mr. Toni Budiono and the entire HKY Sarpras Team, who patiently accompanied and assisted in facilitating every technical requirement within the church premises.

  • Mr. Ronald and the entire Lasika Team, for their dedication, precision, and extraordinary teamwork in refining the installation and executing the hardware rearrangement in the field.

  • All parties, church administrators, and colleagues who contributed to the smooth execution of this project from inception to completion, whom we cannot mention individually.

Design, System Engineering & Acoustic Calibration Team:

  • Room Acoustic Analysis & Calculation, Speaker Position Prediction & Correction, Sound System Electronics Calculation, DSP & Amplifier Configuration (Crossover & Filtering), and Time-Delay Calibration (FRESL Researcher & GCEDAC Software Developer): Hardy Nanda

  • Calibration Companion (Critical Listening): Anak Agung Made Ruandaru

  • Technical Support & Official Partnership: PT Daru Jaya Proaudio

Copyright © 2026 by Hardy Nanda.
It is strictly prohibited to copy, duplicate, or republish part or all of the contents of this document in any form—whether on blogs, social media, messaging groups, or print media—without citing the author's name (Hardy Nanda) completely and clearly, or without the explicit written permission of the author. This includes the article, acoustic and electronic calculation analyses, technical floor plan illustrations, and the GCEDAC (FRESL) calibration methodology. Parish historical excerpts and hardware brands mentioned in this manuscript remain the intellectual property of their respective original rightsholders.

© 2026. All rights reserved.

Contact PT Daru Jaya Proaudio directly for GCEDAC professional sound system calibration or for precision solutions in acoustics and sound system
Tap here for the WhatsApp number

Jl. KEJAKSAAN 32, BANDUNG 40111, JAWA BARAT - INDONESIA
+62 851 8306 6323